Written by Jackson B.
Quick answer: Our Print Profiles are published as settings tables, not preset files. To use one, start from your slicer's closest generic filament preset, enter our temperature, cooling and retraction values, and save it as a user preset. Then run flow and pressure advance calibration, and export the finished preset to back it up or share it.
Our Print Profiles pages list recommended settings for OzFDM filament on specific printers: nozzle and bed temperatures, speeds, layer height, fan, retraction, drying and nozzle notes. A slicer does not read those tables directly, so the job is to turn a table into a saved filament preset that you can pick from a drop-down every time you load that roll.
This guide shows where each value goes, then walks through creating, calibrating, exporting and importing a filament preset in Bambu Studio, OrcaSlicer and PrusaSlicer. Menu names can move slightly between versions, so if something is not exactly where we describe, check your slicer's documentation.
Where each profile value goes
A filament preset does not hold every setting. Temperatures, cooling, flow and retraction overrides live in the filament preset, while speeds and layer height live in the process or print preset. The table maps each field on our profile pages to the right place.
| Profile page field | Bambu Studio and OrcaSlicer | PrusaSlicer |
|---|---|---|
| Nozzle temperature | Filament preset: nozzle temperature for the initial layer and other layers | Filament Settings, Filament: extruder temperature, first layer and other layers |
| Bed temperature | Filament preset: bed temperature for the plate type you use | Filament Settings, Filament: bed temperature |
| Fan speed and first layer fan | Filament preset: Cooling | Filament Settings, Cooling |
| Retraction distance and speed | Filament preset: Setting Overrides | Filament Settings, Filament Overrides |
| Print speed and first layer speed | Process preset, with the filament's maximum volumetric speed as a cap | Print Settings, Speed, with maximum volumetric speed under Filament Settings, Advanced |
| Layer height | Process preset | Print Settings, Layers and perimeters |
| Dry filament, enclosure, nozzle type | Not slicer settings: sort these out before printing | Not slicer settings: sort these out before printing |
As a worked example, our TPU on Bambu Lab X1 Carbon profile recommends a 230°C nozzle, a 40°C bed, 30–60% fan with the fan off for the first layer, and 0.4 mm of retraction at 30 mm/s. All of those go in the filament preset. Its 30–60 mm/s print speed and 15–20 mm/s first layer speed go in the process preset.
If your slicer caps speed with maximum volumetric speed, you can work out the flow a given speed needs: layer height × line width × speed. At a 0.2 mm layer and a 0.42 mm line, 60 mm/s works out to about 5 mm³/s.
Bambu Studio: create a custom filament
Bambu Studio has a dedicated custom filament tool, described in Bambu Lab's guide to creating custom filaments.
- Update Bambu Studio and sign in. Bambu's documentation notes that custom filaments rely on cloud sync, so presets follow your account to the printer.
- Open the filament settings from the settings icon next to the filament list, go to Custom Filaments and click Create New.
- Enter the vendor (OzFDM), the filament type (for example PETG) and a name (for example Basic). Choose the closest base filament, such as the generic preset for that material, and tick the printers you use.
- Bambu Studio names the preset in the form Vendor Type Serial @Printer and adds it to your user presets.
- Open the new preset, enter the temperatures, cooling and retraction values from our profile page, and save.
- To add the same filament for another printer later, use +Add Preset, pick the printer and base preset, and confirm.
Bambu's cloud sync supports up to 20 printer presets, 100 process presets and 200 filament presets. Past those limits, presets stop syncing, but manual export and import still work.
Calibrate in Bambu Studio
Bambu Studio has two calibrations that matter for a new filament. Flow Dynamics calibration finds the pressure advance (K) value, and Flow Rate calibration finds the flow ratio. Both can run automatically on supported printers or manually from the Calibration tab.
- Manual flow rate calibration has a coarse pass (80–120% in 5% steps) and a fine pass (91–100% in 1% steps). Pick the block with the smoothest top surface, then save the value to your filament preset.
- Manual flow dynamics calibration prints test lines, and you choose the value that gives the most even line.
- Saved K values can be assigned to each AMS slot from the material settings on the Device page.
Bambu recommends calibrating when you introduce a filament of a different brand or model, and warns that damp or transparent filament can give unreliable results. Dry the roll first.
OrcaSlicer: save a user preset
OrcaSlicer grew out of Bambu Studio, so its filament settings are laid out in a similar way. Custom filaments are saved as user presets.
- Select your printer, then choose the closest system filament preset, such as the generic preset for your material.
- Click the edit (pencil) icon beside the filament to open its settings.
- Enter the nozzle and bed temperatures, then the fan values under cooling and the retraction values under Setting Overrides.
- Click the save icon, choose to save it as a new user preset, and give it a clear name that includes the printer and nozzle, such as "OzFDM PETG Basic X1C 0.4".
Calibrate in OrcaSlicer
Both calibrations start from OrcaSlicer's Calibration menu, and the results are saved into the filament preset. The flow ratio and pressure advance pages in the OrcaSlicer wiki have full detail.
| Calibration | Methods offered | How to read it | Where the result goes |
|---|---|---|---|
| Flow ratio | YOLO (recommended) or the older 2-pass method | Pick the smoothest top surface with no gaps between the pattern arcs. YOLO: old ratio plus or minus the modifier. 2-pass: old ratio × (100 + modifier) / 100. | Flow ratio in the filament preset |
| Pressure advance | Tower, Pattern or Line | Choose the value with the cleanest corners and most even lines. The Line method depends heavily on first layer quality. | Enable pressure advance in the filament preset and enter the value |
If you send OrcaSlicer's pressure advance test to a Bambu Lab printer, the OrcaSlicer wiki advises leaving the printer's flow calibration option unticked.
PrusaSlicer: save a filament preset
- Switch to Expert mode so every setting is visible.
- Open the Filament Settings tab and select the closest system filament for your material.
- On the Filament page, enter the extruder and bed temperatures for the first layer and other layers, and leave the extrusion multiplier at its default for now.
- On the Cooling page, enter the fan values. On the Filament Overrides page, tick and enter retraction length and speed.
- On the Advanced page, you can set a maximum volumetric speed to cap how fast the filament is pushed through the nozzle.
- Click the save icon, name the preset and save it.
Calibrate in PrusaSlicer
Prusa's knowledge base describes two ways to set the extrusion multiplier. The visual method adjusts the multiplier by 1–2% based on the top surface. The precise method prints a single-wall cube in vase mode and divides the extrusion width by the measured wall thickness.
For corner blobs and gaps, Prusa's MK3-family printers use linear advance, set with the M900 line in the filament preset's custom G-code. According to Prusa, the MK4 family, XL and MINI switched to pressure advance from firmware 5.0.0. Prusa's knowledge base points to community test prints for finding a value, such as the PrusaSlicer pressure advance test on Printables. For the theory behind both calibrations, see our guides to flow rate calibration and pressure advance tuning.
Export, import and share presets
Once a preset prints well, export it. A copy on another drive protects your calibration work if you reinstall, and it is the easiest way to set up a second computer or share settings with a friend.
| Slicer | Export | Import | File types |
|---|---|---|---|
| Bambu Studio | File, Export, Export Preset Bundle, then choose a filament bundle or filament presets | File, Import, Import Configs | .bbsflmt filament bundles, .zip presets, .bbscfg printer bundles and .json |
| OrcaSlicer | File, Export, Export Preset Bundle: printer config bundle, filament bundle, or printer, filament and process presets as .zip | File, Import, Import Configs | OrcaSlicer bundle files and .zip |
| PrusaSlicer | File, Export, Export Config (current profile) or Export Config Bundle (all custom settings) | File, Import, Import Config or Import Config Bundle | .ini (Import Config also reads .gcode sliced in PrusaSlicer) |
A few tips when sharing:
- Name presets clearly. Include the material, printer and nozzle size so nobody loads a 0.4 mm TPU preset on a 0.6 mm nozzle.
- Share the numbers too. PrusaSlicer uses .ini files and Bambu Studio and OrcaSlicer use their own formats, so if you are moving between PrusaSlicer and the other two, copy the values into a new preset.
- Back up before you uninstall on a Mac. The OrcaSlicer wiki warns that uninstalling on macOS can prompt you to delete the configuration folder, and confirming removes every user profile.
Troubleshooting custom filament presets
Bambu Lab's wiki lists a few common problems with custom filaments in Bambu Studio:
- The printer shows a question mark after you set a custom filament from Bambu Studio. Set the filament on the printer's screen first, then set it from Bambu Studio again.
- A custom filament shows [Action Required]. Click it to open the Edit Filament page, delete the highlighted presets and create the filament again.
- Custom filaments are missing in LAN mode. Create the filament while the printer is connected to the cloud, then open the filament settings on the printer so it downloads the data.
Shop the materials in this guide
- 1.75 mm PLA Basic Filament - 1 KG: an inexpensive roll for running first calibrations on a new printer.
- 1.75 mm PLA+ Filament - 1 KG: our everyday PLA and a sensible first custom preset.
- 1.75 mm PETG Basic Filament - 1 KG: functional parts, and a good second preset once PLA is dialled in.
- 1.75 mm TPU95A Filament - 1 KG: the flexible filament used in the worked example above.
Frequently asked questions
Can I download OzFDM preset files?
No. Our Print Profiles pages publish settings as tables, and the steps in this guide turn a table into a saved preset in any of the three slicers.
Do I need a separate preset for each printer?
It is the tidy way to work. Our profiles list different speed limits for different printers, and Bambu Studio creates custom filaments for the printers you select. Add another printer later with +Add Preset.
Why does my Bambu printer show a question mark for my custom filament?
Bambu's fix is to set the filament on the printer's own screen first, then set it again from Bambu Studio.
Should I calibrate flow for every roll?
Calibrate when you change brand or material. Bambu also notes that damp or transparent filament can give unreliable calibration results, so dry the roll before you start.